Differences

This shows you the differences between two versions of the page.

--- supported_modules:hs-wd100 [2018/07/09 19:04] – [Known Issues] removed the flickery LED stuff James Sentman
+++ supported_modules:hs-wd100 [2023/02/13 14:52] (current) – external edit 127.0.0.1
@@ Line 16: / Line 16: @@
 ^Gesture^Code^
-|Single Click|128|
+|Single Click|1|
-|Double Click|131|
+|Double Click|3|
-|Triple Click|132|
+|Triple Click|4|
-|Hold|130|
+|Hold|2|
-|Release of Hold|129|
+|Release of Hold|1|
-The HS-WD200+ dimmer also adds the following extra gestures
-^Gesture^Code^
-|Quadruple Click|133|
-|Pentuple Click|134|
-Yes, thats right you can do up to a 5 click macro for each button with the HS-WD200+!
+The [[supported_modules:hs-wd200|HS-WD200+]] supports all those as well as a quadruple and pentuple click.
@@ Line 71: / Line 64: @@
 </code>
+===Set Data===
+via the [[dictionary:unitcontrol:setdata|Set Data]] verb it is possible to set various parameters in the switch. Note that the parameters of the WD100 are different than the [[supported_modules:hs-wd200|WD200]]. This is a grid of the most useful parameters that can be set for the WD100+ note that this might change in future firmware versions or hardware revisions so you should verify against the latest version of the user manual that comes with your specific unit before issuing the command. It is entirely possible to brick a dimmer if you issue the wrong commands to the wrong addresses. It’s nice to note however that the WD100 an WD200 share the same parameter number for orientation, and then the WD200 parameters start at 11 so if you confuse the 2 device types when setting data they happily ignore the out of range parameters and do not do anything damaging. if you confuse them with switches from other manufacturers then things could be unpredictable.
+^Parameter^Description^value^Example^Default^
+|4|Sets paddle’s load orientation| 0 = top of paddle turns load on or 1 if you need to invert it so that the bottom of the paddle turns the load on.| tell xUnit “name of unit” to setData( 4, 1, 1) to invert the direction if the switch is upside down|0|
+|7|Sets the remote control ramp rate step resolution. | 1-99, 1  being the default and highest resolution|tell xUnit “name” to setData( 7, 1, 1)|1|
+|8|Remote control Ramp step Speed|1-255 maps between 1 and 10 ms between steps| setData( 8, 1, 1) set to 1ms for a quick fade|3|
+|9|Local control ramp rate step, the dim rate when controlled locally|1-99, 1=slowest dimming|setData( 9, 1, 99) set to 99 for faster fade |1|
+|10|Local control ramp rate step speed|1-255 note this value is 2 bytes long! 1=10 milliseconds| setData( 10, 2, 1) set to 1 for a faster local control|3|
+These dimmers let you set the local ramp rate and the remote control ramp rate separately, but as is standard in ZWave you cannot include a ramp rate in individual commands. Each one is made of 2 different parameters. The step resolution which appears to be the number of steps it goes through to get to the preset level, and the speed at which it switches between the steps. For some LED lights it may make sense to set a faster ramp rate since they tend to not come on immediately. Some experimentation with the 2 values may be needed to find the ramp rate that you like best for a specific application.
-===Known Issues===
-As of XTension 9.4.6 the central scene events may be sent more than once. This is a known issue and as soon as I can figure out how to filter repeats of them I will do so. Until then your scripts may run more than once. This isn’t generally a problem as turning on or off a device that is already at the same level doesn’t cause any trouble except extra commands to the systems. If you wish you may be able to check the time delta of the unit and ignore a central scene event if it is less than say 2 seconds since it changed state. Or save off the current date in the central scene handler to a local script variable and compare that script variable with the current date when it’s called. If it’s less than 2 or 3 seconds since it last handled a central scene command then ignore it.